8 inch ford rear end identification.
In most cases, the short axle goes in the driver's/left side. In the above video, you'll see us installing the axle, then measuring out to the end of the bearing. You can also stick a tape measure into the axle tube and measure to the stop in the differential. As we measured, we did not account for the thickness of the backing plate.
This is just a simple video part of the ls Swap Jeep Ford 8.8 axle build showing what the axle tag means.The aftermarket considers this an 8 inch diff. Ford is being specific on the ring gear diameter. The diameter is determined by the number of teeth that are on the gear. If you were to get a different gear ratio it may measure 8 in or it may fall in between 7 3/4 in or 8 in. To get parts just refer to it as an 8 inch. The backlash can be adjusted.Gutter guards are a great way to maintain your home. Our guide breaks down the best 7-inch gutter guards to help you shop with ease. Expert Advice On Improving Your Home Videos Lat...The code appears as a number or letter/number combination in the ‘Axle’ column of the label. If you look at the ‘AXLE’ section on the label above, you’ll see that this Ranger has a ‘F7’ axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer ...IIRC the only trucks that come with the 8.8 rear is the 3.5L N/A trucks. The 5.0L and all others come with the 9.75. That was true up until the '15 model year, Tim. For '15+ the only trucks that always have the 9.75" axle are those with the 3.5L EcoBoost engine. Max Tow might put the 9.75" under a 5.0L truck, but the majority of them have …
Note the shape of the differential cover gasket. The top and bottom of the 7.5-inch gasket are straight with rounded sides. The 8.8-inch gasket has flat sides, top and bottom, with rounded corners. The venerable Ford 9-inch rear axle was phased out during the late 1970s and the mid-1980s. The 7.5-inch rear axle came out in 1979 and is found in ...The Ford 8.8- and 9-inch rear differentials are two of the most popular and best-performing differentials on the market. While the 8.8-inch differential is commonly used in late-model Mustangs, the 9-inch is the more popular and arguably the most dominant high-performance differential for muscle cars, hot rods, custom vehicles, and race cars. Built from 1957 to 1986, the 9-inch Ford ...
8 3/4 inch rear end. ... They were used much later than that, that size anyway. This seems like a good reference for Ford rear end info. FORDification.com - Decoding Your Ford Rearend's Axle Tag - Page 1 of 17 ... Hello, not sure if this thread is still active but I am trying to decode a Fomoco rear differential ID tag shown below. It is ...
Part Number: 741962. 741962 Pinion Yoke fits Ford 8 inch rear end 25 splines fits 1310 series u-joint 3.219 x 1.125. Click for Larger Photo. FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE. STATUS: IN STOCK. YOUR COST: $89.95. ADD to SHOPPING CART. Click Here to Buy Online.Jan 3, 2024 · Using the Ford Axle Code Chart. Our comprehensive Ford axle code chart is a valuable resource for decoding axle codes. It lists all the known axle codes for various Ford models, allowing you to match the code found on your vehicle with the corresponding differential information. See also Reviving Performance: BMW 340i GT xDrive Wheel Bearing ... A few ways to tell a the difference between a Ford 9" rear end and a Ford 8" rear end. The main way to tell is the 3rd member is flat on top on a Ford 8 inc...Quick ID guide for the Ford 8 in. and 9 inch rear axle. We look at how to determine Equa lok, traction lok and open differentials. We show the best and worst...
GM 9.76” 12 Bolt Rear, 2014-On. GM 10.5” Rear. GM 11.5" Rear End. GM Dana 60. GM / Chevy - Differential Identification Shop by your differential. Please select a rear end that matches your vehicle below. General Motors has a wide range of front and rear ends! We carry everything from the 7.25" IFS front end parts, to the large 11.5" rear ...
1966 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: ... Hello, I have to overhaul a 1966 Mustang Fastback K Code 4 speed manual rear axle,,, the code on the rear axle plate is: WCZ-S / 3.50 SKD980.
Master the complexities of the Ford F150 rear end with this comprehensive guide, helping owners, mechanics, and enthusiasts in proper identification, maintenance, and repair. ... each with distinct characteristics that suit particular applications. Among the prominent models, we find the 8.8-inch and 9.75-inch variants, names indicating the ...The code appears as a number or letter/number combination in the 'Axle' column of the label. If you look at the 'AXLE' section on the label above, you'll see that this Ranger has a 'F7' axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer and Aerostar ...Does anyone know if there are axles for a ford nine inch that are 8 lug. I have a 71 Bronco with full width half ton axles. ... swap rear axle for 8 lug version(60, 14b, 70u, etc.), I don't think moser or any of the other axle companies can make a 8 lug semi floater axle, the blanks they use aren't large enough in dia.(if things have changed ...Ford inch rear end carrier lokFord 8.8 rear axle id tags Ford inch rear end differential difference tell betweenThe 9-inch ford rearend is the strongest rearend out there—it's all due. Ford identification inch front rearend crankshaftcoalition wikiRear end ford mustang chevy bolt comparison 2008 rod hot Exploded nhraBasic id ford 9 inch ...Being a 28 spline axle standard case(not a nodular iron one) your carrier bearing size is likely the most common average size but some out there like for the 1966-77 Ford Bronco used smaller id bearings and some full size Ford cars used larger od bearings. 2.892" od carrier bearings with the 1.780" id are the most common.
Need help decoding tag on Lincoln 8.8" IRS differential. This is an aluminum housing, independent rear suspension Ford 8.8" differential (complete center section). Believed to be out of a Lincoln Mark VII, which would make it a 1984-1992 (if the Mark VII origin is accurate...not positive on this). The unit accepts 28 spline axles.Shop Ford 8 Inch, Disc Brakes and get Free Shipping on orders over $149 at Speedway Motors, the Racing and Rodding Specialists. Ford 8 Inch, Disc Brakes in-stock with same-day shipping. ... Ford 9-Inch Housing Identification and Axle Measurement. Read More. Need help with rear end identification for your muscle car or hot rod? Learn how to ...ive got a 68 mustang 289 auto with an 8 inch out back. im converting it to a 9 inch to accommodate the new engine mods. Ive got the chunk and everything but i dont know if i can use the brake backing plates from the 8 inch and for my new 9 inch. -69 Mustang - 351W AFR 185, Vic Jr, .512 @ 232°, 750 Holley, WC T5, 4.30 TruTrac, CalTracs.Ford 8-Inch Rearend: Good Ol' Spot Repair. Rodney Bauman Writer Nov 02, 2018. See All 29 Photos ... Its hangy-down parts (springs, front axle, rearend, and so on) are glossy, black, single-stage ...Likes: 33. Received 73 Likes on 39 Posts. Visual Confirmation of 10.5" Sterling Rear Axle? According to the rule of thumb (all 250s w/o the HD pkg get the Sterling; truck is a 2019 F250 Powerstroke), I should have a 10.5" Sterling, 35 spline rear axle. Door jamb Axle code is "3H" (3.31, electronic locking)Ford 7.5-Inch and 8.8-Inch Axle Visual Identification: Both axles use (10) bolts to hold on the cover, but there is an obvious difference in their shape. ... The tag above is from a 8.8 inch rear axle in a 2001 Ford Ranger 4×4 extended cab with 4.10 gears. Federal Compliance Sticker:The Ford 8.8- and 9-inch rear differentials are two of the most popular and best-performing differentials on the market. While the 8.8-inch differential is commonly used in late-model Mustangs, the 9-inch is the more popular and arguably the most dominant high-performance differential for muscle cars, hot rods, custom vehicles, and race cars. Built from 1957 to 1986, the 9-inch Ford ...
Hello. WCZ-E is the 8 inch rear end used in C code cars in the 65 and 66 model years. The 2 80 does indeed mean that it is a 2.80 ratio, which would be an axle code of 6 on the door tag, 5MB is a date code, which means the second week of december of 65, which would be a 66 model car, probably built in like mid-january, and the 930 is a ...
The Ford 8.8 rear axle has been a staple of the Ford ... It was first produced in 1983 and has been a common axle used in place of the venerable Ford 9-inch axle assembly. 4WD applications have ...Now, many know that the early 9" rear ends are the same length as the 65/66 8", with most sites stating 52.25" from the outside of the housing flange to outside flange. However, the Kevinstang info states that this measurement is actually from the INSIDE of the flange to flange. My 9" measures 52.25" from inside to inside, which means the ...Currie believes its billet pinion support is more than 25 percent stronger than conventional and stock units. It will fit all 8-inch gear cases and is available in a polished (PN CE-4033P; list ...Paul1958. 5745 posts · Joined 2010. #3 · Jan 8, 2016. Dylans, Here are the 8 and 9 inch carrier housings side by side. See how on the 8 inch (right) there is a clear shot to get to the lowest mounting nut with a socket/extension where on the 9 inch (left) on the same nut (partially visible) you need to use a box wrench as its shrouded by the ...5981 posts · Joined 2007. #17 · May 10, 2010. The 8.8 didn't come out tell the mid 80s and the rear cover has bolts on it like every other rear end out there.The easiest way to tell a 8 inch from a 9 inch is try putting a socket on the lowest bolt on the 3rd member.A 8 inch the socket will go on a 9 inch it won't. Like.Ford Rear Axle Assembly Identification - Page 10: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: C001-A: Crown Victoria, Grand Marquis 92-93: 3.55: 8.8: L: 28 : C002-A:Thanks again everybody for the help. How To Recognize 9-Inch Housing Centers: 1957 - no dimples, flat center band up the center of the rear cover, bottom drain plug. 1958-1959 - two dimples on back of housing, flat center band, some had drain holes. 1960-1967 - two dimples, flat center band, oil level hole in back cover.Differential Identification. Dana Dana 30 - Standard, Reverse Rotation, CS & TJ Dana 30 - JK ... Ford Ford 7.5" Ford 8" Ring Gear Diameter: 7.5" Ring Gear Diameter: 8.0" Pinion Diameter / Spline: 1.625" / 28 Pinion Diameter / Spline: 1.188" / 25
Ford 8 inch limited slip diff options. Hey all, it's been a while, but I'm still kickin' around. Anyways, It's time to start ordering parts and I've got a few questions. 1. I'm rebuilding an 8'' rear end because my little 289 hasn't broken 300 hp and probably won't for a while. I've been looking and really need some advice as to who makes the ...
The image below shows the Safety Label of a Ford Truck. From the arrow, you can see the axle code is H9. As you proceed to the Ford Axle Code chart, you will notice that the table indicates it has a Ford 8.8″ Limited Slip Differential with an Axle Ratio of 3.55. Find the axle code from the Safety Compliance Certification label.
Note the shape of the differential cover gasket. The top and bottom of the 7.5-inch gasket are straight with rounded sides. The 8.8-inch gasket has flat sides, top and bottom, with rounded corners. The venerable Ford 9-inch rear axle was phased out during the late 1970s and the mid-1980s. The 7.5-inch rear axle came out in 1979 and is found in ...The 8-inch, removable-carrier rear axle is a scaled-down version of the 9-inch axle. Ford used the 8-inch axle across a huge variety of applications in compact and intermediate-size vehicles from ...1965-66 Mustang 8 inch rear end identification question. I'm doing a six cylinder conversion on a 1965 Mustang. The front end components and everything is done. I purchased a rear axle and third member from Melvin's Classic Ford Parts. I know that the rear end has a 2.80 gear ratio because I counted the ring gear teeth and the pinion gear …My video on how to change the gear oil in a rear differential or rear end. These are universal instructions for most vehicles. It is an easy repair or replac... How to determine the width of the yoke. Shown is a 3 1/ 4" Saddle (1310) You will be measuring the saddle width (where the u-joint cups fit into the yoke). The measurement will be either 3 1/4" (1310) or 3 5/8" (1330) or (1350) The 1350 almost never found in production car driveshafts. The 1310 yoke is the most common. 9 Inch Rear End Differences. We should point out there are three distinct 9-inch axle ends: the late big bearing (Torino) and the early big bearing both take a 3.150-inch od wheel bearing (the difference is in the bolt spacing for the backing plates), the small bearing ends take a 2.834 od bearing with yet a different backing plate bolt pattern. The code appears as a number or letter/number combination in the 'Axle' column of the label. If you look at the 'AXLE' section on the label above, you'll see that this Ranger has a 'F7' axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer and Aerostar ... Shop Ford 8 Inch, Disc Brake Kits and get Free Shipping on orders over $149 at Speedway Motors, the Racing and Rodding Specialists. Ford 8 Inch, Disc Brake Kits in-stock with same-day shipping. ... Ford 9-Inch Housing Identification and Axle Measurement. Read More. Need help with rear end identification for your muscle car or hot rod? Learn how ...The number of times the driveshaft rotates for each rear wheel rotation is your Mustang's rear gear ratio. This is also sometimes referred to as the final-drive ratio since it's the last gear that must turn before power hits the pavement. If you have a rear gear ratio of 3.31, the driveshaft rotates 3.31 times for each wheel rotation.Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WEM-A: Bronco '66-'71: 4.11: 8 3/4 in: NL: 28: 2780 lb Axle: WEM-A2: Bronco '70-'73: 4.11: 9.0: NL: 28:Ready to complete your budget rear axle overhaul? In this final installment of our series, join us as we guide you through every step of how-to assemble the ...The BOM stamp (2) or Axle Identification Tags (2A) are used to identify Dana axles / differentials. The BOM will identify the model number, the gear ratio, the type of axle / differential, and component parts. Traditional BOMs are 6 digits followed by 1 or 2 digits, and start with the numbers 60 or 61. On some tags, the first 2 digits won't ...
1947 and Older Ford Trucks; Bronco. 2021+ Bronco; 2021+ Bronco Sport; 1978 - 1996 Big Bronco; 1966 - 1977 Early Broncos; Bronco II; Ford Vans and other vehicles. 2014+ Transit; Transit Connect; 1968-Present E-Series Van/Cutaway/Chassis; Ranchero & 1961 - 1967 Econoline; Nite, Nascar & Other Limited Edition Ford Trucks; Performance, Engines ...Mr. Regular leans how to identify a Ford 7.5 vs a 8.8 by the differential cover. The Vagabond Falcon needs a Ford 8.8 rear that is 56 inched hub-to-hub9" stuff is so cheap compared to 8" stuff due to popularity. Spend a bunch of dough to make an 8" handle 400 fwhp or spend the same or less and have a 9" that will handle whatever you put on it years from now. Personal opinion: I highly doubt you can build an 8" to handle 400 hp cheaper than you could do a 9".Get the best deals for rear end 9 inch ford at eBay.com. We have a great online selection at the lowest prices with Fast & Free shipping on many items! ... FORD 9 INCH 2.75 REAR END OPEN DIFFERENTIAL ID TAG. Opens in a new window or tab. Pre-Owned. $24.00. mustangclassics (580) 100%. or Best OfferInstagram:https://instagram. monro ogdensburgdmv orlando west oaks mallmatamoras pa gun showdoes tyler hynes have a brother Housing Identification. 57 - no dimples, flat center band up the center of the rear cover, bottom drain plug. 58-59 - two dimples on back of housing, flat center band, some had drain holes. 60-67 - two dimples, flat center band, oil level hole in back cover. 63-77 Lincoln, LTD, Thunderbirds had 9.375 inch centers, housings were cut away at the ...At least the rear end appears to be original. Dave R. I recall reading somewhere that only 428CJ and Boss 302 cars received 31 spline axles. The best way is to pull the axle. While it is possible to identify a factory axle from the outside, the same rules do not apply to aftermarket axles. hotels off route 80 in ohiodunn ave nail salon Differentials: Identification, Restoration, & Repair 2nd Edition. $29.95. 1 Tube Gear Marking Compound Grease - Ring & Pinion Gears - Rearend - Ford Chevy. ... 10 - Ford Copper Housing Washers - 9" Inch & 8" Ford Rearend Axle - NEW. $10.00. 8.8" Ford Pinion Nut - 8.8 Inch . $5.85. 9" Inch Big Ford Old-Style 1/2 Housing Bearing Ends (1 Pair - 2 ...When it comes to getting power to the pavement, GM's 10-bolt, 8.5-inch rear end with Positraction is a hero. Like Superman in street clothes, however, it can be hard to identify this beefy unit among its weaker cousins, the 10-bolt, 8.2-inch with open differential. GM built countless thousands of both types of 10-bolts from 1970 to 1994. 60 crips Ford inch rear end carrier lokFord 8.8 rear axle id tags Ford inch rear end differential difference tell betweenThe 9-inch ford rearend is the strongest rearend out there—it's all due. Ford identification inch front rearend crankshaftcoalition wikiRear end ford mustang chevy bolt comparison 2008 rod hot Exploded nhraBasic id ford 9 inch ...1965-66 Mustang 8 inch rear end identification question. I'm doing a six cylinder conversion on a 1965 Mustang. The front end components and everything is done. I purchased a rear axle and third member from Melvin's Classic Ford Parts. I know that the rear end has a 2.80 gear ratio because I counted the ring gear teeth and the pinion gear … Ford 8.0 Ring and Pinion Part Number, Tooth Count & Ratio. Your gears run cooler and last longer! Order above high performance synthetic oil and friction additive combo kit at time of order for ring and pinion or bearing overhaul kit and pay only $63.95 plus S&H, a $69.00 value.