Ford axle identification.

Ford ID number: E4TA-AKD / Dana ID number: 610229-2 = Dana 44 / 3.54-1 / Free Running Hubs / non Limited Slip / 3850 lb Front Axle Capacity. 1980/89 Ford Light Truck Parts Catalog, Front Axle Parts List # 30.3AR.Identifying Your Rear Axle Flange. Ford, Chevrolet, Oldsmobile, Pontiac, they all used a different axle flange at one point or another. Being able to identify the flange you have can spare you a lot of grief when it comes time to buy parts, not to mention speeding up the process as a whole. Check out the graphic below to help you identify …Ford Rear Axle Assembly Identification - Page 09: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. 79-82 Lincoln & Town Car 80-81 Lincoln & Town Car '82 Mercury 80-82: 2.73: 8.5: NL: 28-WGY-A2: Ford Pass. 82-83 Lincoln & Town Car '82-83 Mercury 82-83: ...Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28-

Axle Identification Chart. DANA 25/27 These Danas are indistinguishable in appearance. The military Model 25 has a thick, cast cover, while the 27 and civilian-model 25s have a thinner cover, will accept taller gears, and backed V-6s. DANA 28 The alloy-case Dana 28, with a 6 5/8-inch-diameter ring gear, came in Bronco IIs and …The solid axle in a F-150 is also a "live" axle, because it transmits power to the wheels. A solid axle is comprised of: Axle tubes welded to a differential housing. Differential cover. Axle shafts that run inside the axle tubes. Differential gears that transmit power from the driveshaft to the axleshafts. Wheel bearings in the outer end of the ...Ford Aerostar - The Ford Aerostar 8.8-Inch axles had 28-spline shafts. NOTE: Increasing from a 28-spline to a 31-spline axle allegedly increases strength of the axle shaft by 34%, however I'll go by the capacity ratings of the axle assemblies provided by the manufacturer. Ford Rates the Ranger axle at 2750 lbs and the Explorer axle at 3200 lbs this is a 16% increase in strength, which ...

2002 F350 DRW 6Sp 7.3L Flatbed. I bought this truck used in '06 - door sticker states "incomplete build" as I think this truck was originally ordered as a cab and chassis. The Axle code on the door sticker is blank. Axle: Looking at the tag on the rear diff cover, this is what I see: V2C34 YB. 606773-6 LS.

E-350 Dana axle M70FF (M267FF). 3.28 qt (3.1 L) 1. E-450 Dana axle M70HD (M273HD). 4.86 qt (4.6 L) 1.Four well-known names -- Meta Platforms (META), eBay (EBAY), Qualcomm (QCOM) and Ford Motor (F) -- kicks off value investor Jonathan Heller's 2023 Tax Loss Selling Recovery Por...mustange70. 4031 posts · Joined 2005. #8 · Nov 17, 2005. the pre superduty trucks used dana 80's (easy way to tell is if it has disc brakes its a dana 80) and all f-350/f-250 used the 10.25 from the mid eighties up to the superduties, then the superduties as far as i know the 250/350 all used the 10.5 and the 450 and up used the dana 135, but ...1987 - 1996 F150 & Larger F-Series Trucks - Axle ratio identification help - I have a 1989 F150 4x4. I am unsure of my axle ratio's and with good reason. The door code says 18, which I know is 3.08 Non-LS. The guy I bought the truck from told me that he replaced the rear axle with a different ratio.Ford Rear Axle Assembly Identification - Page 16: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V012-A: Ford Pass., Mercury 86-91: 2.73: 8.8: NL: 28-V012-B:

Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.

1961 - 1966 F-100 & Larger F-Series Trucks - Front axle identification-no axle code on name plate - Forum Folk! Does a 1963 B500 front axle have a stamp or any identifying marks? I have a 1963 B500 and the warranty plate has no axle code entered. According to the parts book the '63 B500 should have 14 x 2.5 brakes...

Differential Identification using Tags & Stampings. The most accurate differential identification is provided by the bottom line of the tag number or axle tube stamp. Differential tags can easily be used to identify Dana …Call our staff of experts at 888-382-2953. We're here to help Monday thru Friday from 8AM to 5PM CDT. GM Vehicles come with a RPO code tag, usually located in the vehicles glovebox or door jamb. These tags have a wealth of information about your specific vehicle's equipment and specifications. Read more about GM RPO Axle Identification Codes.Front axle identification. Was hoping some of y'all could help me identify the front axle in my 1971 F250 highboy. My warranty/info plate is missing off the door so can't find out that way. I am guessing it's a Dana 44hd due to 446cf being cast near the deferential cover, but was hoping someone could confirm or deny it.The 1976 and 1977 Ford Dana 60 had a standard spiral, 4.10 ratio gear set. Cover: 10 Bolt, 12" high. Ring Gear: 9-7/8", 12 Bolt. Suspension: Leaf spring. Axle Shafts: 1976-1977 had 1.25"-19 spline outer axle shafts and the external snap ring axle u-joint has 1-3/16" diameter cups. Knuckle Mounting: Open with Greaseable King Pins.Ford Truck Enthusiasts Forums. Older, Classic & Antique Trucks. 1987 - 1996 F150 & Larger F-Series Trucks. 1 TON Axle Identification. Notices. 1987 - 1996 F150 & Larger F-Series Trucks 1987 - 1996 Ford F-150, F-250, F-350 and larger pickups - including the 1997 heavy-duty F250/F350+ trucks. Sponsored by:Ford Rear Axle Assembly Identification - Page 07: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. '82-'83: 3.42: 8.5: L: 28-WFC-G: Capri, Mustang, Cougar 82 Fairmont, Zephyr, Granada 82 Lincoln Continental '82 Thunderbird 82: 3.08: 7.5: L: 28-The front axle is an open differential. Very common to have a rear LS and open front, pretty much industry standard for a long time. I'm not 100% positive but I think the new Tremor for 2020 is the first time Ford is offering a traction upgrade, either locker or LS in the front axle. Reply Like.

Ford used Coil Spring, Dana 44IFS Twin Traction Beam front axles on 1980-1996 Full Size Bronco and F150 4x4 vehicles. These Ford Dana 44IFS front axles are rated at 3500 to 3550 pounds. External Identification Characteristics of Ford Dana 44 Coil Spring Twin Traction Beam Independent Front Suspension Front Axles: Coil Spring Suspension1973-1979 Ford Truck Rear Axle Codes. The first two digits of the axle code identify the ratio and capacity of the rear axle. (The third digit of the axle code identifies the ratio and/or capacity of the front axle, if applicable. CLICK HERE to see a complete listing of front axle codes). For reference, this section from the Ford MPC is posted ...Clutch, Transmission, Differential, Axle & Transfer Case - Tranny & Axle Identification - I had my truck up on my dad's hoist and was checking my manual transmission and rear differential fluid. They both seemed fine but I was wondering what kind of fluid they take in case I want to change it with synthetic. The rear...Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:Differential Identification is the first and most important step in any differential repair or ratio change. Careful differential identification will help make sure you get the right parts for the job the first time. Dana Spicer and Ford Differentials can be identified most accurately by the tag number or axle tube stamp. Go to: Differential TagsTop Axle: Stock 1946 Ford Car. 2nd down: Stock late 1947 Car (getting ready for shock studs no holes) 3rd down: Stock 1948 car (studs for tube shocks) Bottom axle: 4" stretch drop (narrowed a little can also do original width) 1946-48 Dropped Axles are $300 plus shipping - to drop yours. 1942-48 .8125 Kingpin set $100.

Axle codes for Ford Explorer, Ranger and Bronco II. Axle identification Ford Explorer, Bronco II, Ranger.

2009 - 2014 Ford F150 - Axle tag id ON AXLE ITS SELF!!! - so, my local pull it yourself LKQ got a bit of a unicorn middle of last month they got a 2013 F-150 ext cab hit hard in the front. First time I have seen our body style at that yard. The engine and trans were already taken. it is a VERY low miles truck I got...The tag is on the passenger side axle tube. 229 = Dana 50. 248 = Dana 60. If i remember correctly the three digit number is the ring gear size in millimeters (24.8cm/2.54 = 9.76"). If the number is not readable you can still identify the axle by looking at the pinion nose on the center section. Here is my Dana 60.Apr 7, 2023 ... John from JeepsterMan gives us a couple ways to tell what rear axle you're running. Jeepster Commando Rear Axle Parts Link: ...Decoding the Ford 9" Axle Tag. Using the information I found on DIY Ford, I created the following image which represents my attempt to decode the tag I found on the rear axle in my '76 F-150 LWB 4X2. I think that I have figured out the date of manufacture, ratio and presence of a limited slip differential.those are GM military axles out of a m211 truck. Will have either 6.20 0r 6.80 ratio, most were 620s ther good axles for pullin if you are under 1000hp they do make after market parts for them, axles,spools, but its limited stuff, if your planning on getting in big over 1000hp, go to the f 106 rockwell axles, there is a ton of aftermarket parts ...Need help with axle identification! 1961 - 1966 F-100 & Larger F-Series Trucks Discuss the Slick Sixties Ford Truck Need help with axle identification! Reply ... Would assume the whole axle is 1973 or newer Ford. The rear is either Dana 60 or 70 but not an 80 as the diff cover isn't tall enough. Looks like a Dana 60 to me from here.In most cases, the short axle goes in the driver's/left side. In the above video, you'll see us installing the axle, then measuring out to the end of the bearing. You can also stick a tape measure into the axle tube and measure to the stop in the differential. As we measured, we did not account for the thickness of the backing plate.House centipedes can be an unsettling nuisance, but you can get rid of an infestation. Here’s how you can identify and remove a house centipede problem. Expert Advice On Improving ...

Rear axle tag identification. I am trying to identify what kind of axle I just purchased. I was told it came out of a '66 Mustang Coupe with a 289. The axle tag reads: According to fordifcation.com they identified this axle coming out of a '65-'66 Mustang with a 2.80 axle ratio and a 7-3/4" ring gear.

The Ford 8.8 is an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI. It was first used in model year 1983 Ford trucks. The axle was developed to replace the Ford 9-inch axle. This axle is still in production today for a variety of Ford vehicles.

1968 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 0: 2.50 open differential: 1: 2.75 open differential: A: 2.75 locking differential: 2: …Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle Identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines.Clutch, Transmission, Differential, Axle & Transfer Case. 1. 09-08-2004 09:00 PM. /. 2004 - 2008 F150 - Axle identification - On my 04 lariat 4x4 the axle code is 26, which from my research says 3.73 non limited slip. Which a 4x4 with non LS is a sad thing. But when I spin the tires they both spin.Oct 28, 2020 ... How "I" rebuild a Ford 8.8 differential. ... Pinion Ring Gear Mesh Noise Identified Looking for advice in Youtube Land ... #ETCGDadsTruck Axle/ ...If you are fortunate enough to find an axle with the identification tag still attached, it will help solve part of the mystery of what application the axle came from and what might still be inside. The axle identification tag is located at about the 3 o’clock position under the third-member mounting nut when you are looking straight at the ...The '05+ front has radius arm mounts case into the pumpkin, '99-'04 has leaf spring pearch. The '05+ front will have the 3 bolt, thin silver dialout hub with "FORD" turn knob, the '99-'04 will generally have the cheap black plastic dialout and turn knob. Rears are both 10.5" Sterlings for the SRW trucks. Don't know a quick way to ID them off ...1959-1979 Ford Dana 30, Dana 44, and Dana 60 front axles were stamped on the front of one of the tubes (usually the left tube) with an axle identification or Bill of Material (BOM) Number. From about 1965-on, a stamped metal tag with the BOM number was...Keep in mind as mentioned, the Fairlane spring perch distances were not the same as the Mustang. All the Galaxies I have seen from throughout the 1960's used the 9-inch rear, regardless of engine size. Axle Widths: 1965-1966 Mustang 57.25 inches. 1967-1970 Mustang 59.25 inches. 1971-1973 Mustang 61.25 inches.Chrysler 11.5” Rear. Chrysler 11.8” Rear. Dodge Dana 60. Chrysler / Dodge - Differential Identification Shop by your differential. Please select a rear end that matches your vehicle below. Chrysler has a wide range of front and rear ends! We carry everything from the 7.25" front and rear end parts, to the large 11.8" rear end parts for Ram ...Ford 9" Rear Axle Information. The 9" Ford rear axle, so called because of a 9" ring gear diameter, is the choice of many circle track racers because of its strength, availability and ease of maintenance. Produced from 1957 to 1987 by the Ford Motor Company, it was used in full size Ford, Mercury and Lincoln passenger cars, ½ ton pickups ...At least the rear end appears to be original. Dave R. I recall reading somewhere that only 428CJ and Boss 302 cars received 31 spline axles. The best way is to pull the axle. While it is possible to identify a factory axle from the outside, the same rules do not apply to aftermarket axles.

Apr 9, 2018 · 36192 posts · Joined 2008. #5 · Apr 9, 2018. a wide track is a wider dana super 60 and it is beefier plus it turns sharper. but it always comes with wider wheel well flares and it was not an available option in a SRW. Like. 1967 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 8: 2.75 open differential: H: 2.75 locking differential: 6: 2.80 open differential: F: 2.80 locking differential: 2:There is two different nuts for the early Ford spindles. 1928-35 Have a larger (taller) nut. In 1936, Ford went to a shorter castle nut. All threads are the same (3/4-16) Early Ford spindle identification & information including details from the 1920's, 1930's & 1940's. Specifications and sizes to educate about early Fords.Instagram:https://instagram. walter whites confessiondaily bulletin pueblo copernats meatsclaremont nh police log Differential Identification Work Page. Accurate Differential Identification is the first and most important step in your differential repair, upgrade or overhaul project. The following information is provided to help you identify the differential you are working on. If in doubt, consult one of our differential experts at (800)510-0950! i just figured since you got the front, the rear was also 2000year model. you're right, its a 10.25. Personally since you already have metric up front, id sell that axle and just get a 1999+ 10.5" rear (same thing) with discs and metric pattern. Shop.FarmboyFabrications.com. 239.337.LIFT. bmv goshen iniready placement chart By doing a Vehicle Identification Number or VIN number check, you can go and check any Ford online store for parts that you're looking to get. Whether it's for your Ford truck or sedan you can search for tires or even for parts for your engine block, just by having the VIN code. So make use of the free VIN check services and you can never go wrong.Ford used Coil Spring, Dana 44IFS Twin Traction Beam front axles on 1980-1996 Full Size Bronco and F150 4x4 vehicles. These Ford Dana 44IFS front axles are rated at 3500 to 3550 pounds. External Identification Characteristics of Ford Dana 44 Coil Spring Twin Traction Beam Independent Front Suspension Front Axles: Coil Spring Suspension envision eye care bristol Received 2,739 Likes on 1,330 Posts. Quote: Originally Posted by 99150. Count the bolts on the cover. 12 bolts, you have a 10 1/2" sterling. 14 bolts, you have a Dana M275. Also, if the fill plug is in the cover, you have a DANA. I don't *THINK* they put the 10.25 sterling in the F250. The 10.25 hasn't been in a F250 since 1997.My truck is not near me. Thanks. These are part numbers, will not be marked on the axles, as numbers marked on axles would be ID engineering numbers. B7C-3010-A .. Front Axle / Obsolete ~ 1957 F100/250. B8C-3010-A .. Front Axle / Obsolete ~ 1958 F100/250; 1959/60 F100/250 2WD. Originally Posted by NumberDummy.