Detroit 60 series starting problems.

Table 2. Series 60 Engine Air System, Fuel System, and Cooling System Parameters. * Exhaust systems should provide a maximum of 3.0" Hg during normal service. This applies to exhaust system devices having mufflers and diesel oxidation catalysts. Particulate filter engines may operate above 3.0" Hg specification as long as they do not exceed ...When removal of the crankshaft becomes necessary, first remove the transmission, then proceed as follows:‪. Steam clean the exterior of the engine. Refer to "1.1.3 Cleaning the Cylinder Block" . Drain the cooling system. Refer to "14.6.4 Cooling System" . Drain the lubricating oil. Refer to "14.6.1 Lubricating Oil" .Detroit series 60 12.7 fuel issues. I have been having a heck of a time trying to source my issue with air in my fuel system. It all started after truck would sit a few days. It would be hard to start then be good once running but then became problematic and needed the fuel tank pressurized to start and it would still get air after running a ...Series 60 Air Temperature Sensor. On DDEC III/IV engines there is an Air Temperature Sensor (ATS) mounted to the bottom of the intake manifold. The ATS sends an electrical signal to the ECM indicating the inlet manifold temperature of the air entering the engine. The ECM uses this information to adjust gas flow, control air fuel ratio and in ...To determine if a faulty fuel injector is causing the cylinder to misfire, perform the following steps: ‪. Install DDL adaptor to the data cable and plug the adaptor into the DDL connector in the vehicle; refer to OEM guidelines. Start the engine. >From the DDEC III/IV Select Menu, scroll to select ENGINE and press the ENTER key.

I can't get a good answer on when to replace the water pump on a Series 60, even from a Detroit dealer. My main concern is the potential of losing the water pump on a trip. The only answer of any sort I have received is to replace when it starts weeping coolant. MY bus has somewhere over 300,000 miles and no indication the water pump has ever ...

Series 60 - STARTING DIFFICULTY - ENGINE ROTATES - EXTENDED CRANK TIME. There are no fault codes present and the engine finally starts after an extended crank time. 4.13.1 Fuel Level/Leaks Check…Detroit Diesel Series 60 engine will not start - Answered by a verified Technician ... Detroit Diesel Series 60 engine will not start. Customer Question. ... 1998 Freightliner series 60 Detroit multiple fuel related problems after sitting for periods of time when engine is first started sounds like it's running on one cylinder very very rough ...

4. Start and bring engine up to operating temperature (over 140°F/60°C). 5. Verify operation is satisfactory and no warning lamps illuminate. If warning lamps illuminate, troubleshoot the codes. If assistance is required, call the Detroit Diesel Customer Support Center at 313-592-5800. 23.3 SPN 84/FMI 4The Detroit Diesel 60 Fault Codes guide is an essential resource for anyone working with these engine models. It empowers technicians, mechanics, and fleet managers with the knowledge and instructions necessary to diagnose, troubleshoot, and resolve issues related to the Series 60 engine, ensuring optimal performance and reliability. Language: RU.The following procedure will troubleshoot Flash Code 61.‪. Section 60.2.1. Test Alternator Ground. Perform the following steps to test alternator ground.‪. Disable …Great place to get rebuild parts for cheap! To answer your question: you are paying way to much for a Detroit Diesel Label...the in-frame kit for an 11.1L or 12.7L series 60 is $2,200 for an engine with an oldstyle piston and $2,500 for an engine with a new style piston. The Detroit Diesel® Series 60 engine is a reliable and powerful engine, but like any engine, it can experience problems. One of the most common issues with the Series 60 is ECM (Engine Control Module) problems. Understanding the causes of ECM problems can help you diagnose and fix them quickly and efficiently. The most common cause of ECM ...

Truck Maintenance - help with fuel problem detroit 60 series 1995 - I have a detriot 60 series engine that took me 40 seconds to start once i started it I drove it for 15 minutes then I cutt it off and it would crank. I put 2 used fuel pumps on oday and none of them worked. i took the lines off the fuel pump to see if

201. 95. Feb 13, 2009. California. 0. Just purchased 2000 Fld120, with detroit 60. After driving it for about 30 minutes, noticed the engine surges, up to 1500 rpm's when idled (intermittently). Once its in gear, it will lower rpms, enough to start off, but then intermittently throughout the gears the engine will begin to surge again.

Hard start on a series 60. New injectors, head, bullgear, sensors, fuel system. Also tested with known good ECM and program. It was approximately 15C (...Series 60 – STARTING DIFFICULTY – ENGINE ROTATES – PLUGGED FUEL FILTER(S) To determine if a plugged fuel filters is causing starting difficulty, perform the following steps: 1. Disconnect the fuel line…Series 60 - Section 1.28 Camshaft and Camshaft Bearing; Series 60 - Section 1.27 Thrust Plate Perimeter Seal; Series 60 - Section 1.24 Gear Train and Engine Timing; Series 60 - Section 1.25 Compact Gear Train and Engine Timing; Series 60 - Section 1.26 Camshaft Gear Assembly Series 60 Exhaust Gas Recirculation (EGR) Model5 Apr 2023 ... Dakota shows how to check the ECM or computer of a Detroit series 60 engine and some bonus footage of how to properly take off a driveshaft ...Table 2. Series 60 Engine Air System, Fuel System, and Cooling System Parameters. * Exhaust systems should provide a maximum of 3.0” Hg during normal service. This applies to exhaust system devices having mufflers and diesel oxidation catalysts. Particulate filter engines may operate above 3.0” Hg specification as long as they do not exceed ...

Working on 91 detroit 11.1 60 series hard to starter up after 5 mins sitting had to use starting fuel - Answered by a verified Technician. ... Working on a 1996 international 8100 with M11 Cummins engine. I am having a problem with starting. I am having an issue with the tuck losing fuel prime.The Detroit 60 Series engine is a 12.7 liter inline 6-cylinder diesel engine that was released in 1987 and is still used today. Torque specs for the bolts vary depending on the application, but generally range from 30 to 80 ft/lbs. The cylinder head bolts should be torqued to 50 ft/lbs (67 Nm) dry, then re-torqued at 180 degrees rotation to 35 ...Detroit series 60 15:1 issues Discussion in 'Trucks [ Eighteen Wheelers ] ' started by DDS60, ... They'll stop smoking when you start it, but will smoke if you release the brake before they warm up. If 1/2 mode masks the problem, get it reflashed. Or overhaul it again with the higher compression pistons.Generally, the drive by the wire system often comes with more wiring issues, as well as TPS problems. For instance, the engine brake may fail. At this point, programming is required after replacing the engine brake. Another issue with the Detroit diesel series 60 is zero throttle or having a limited throttle response.When removal of the crankshaft becomes necessary, first remove the transmission, then proceed as follows:‪. Steam clean the exterior of the engine. Refer to "1.1.3 Cleaning the Cylinder Block" . Drain the cooling system. Refer to "14.6.4 Cooling System" . Drain the lubricating oil. Refer to "14.6.1 Lubricating Oil" .

Detroit 60 series 12.7L Egr problems ... ddec 5 is down I can no longer pull loads with it and not one shop can give me a answer on the dyno today the the truck starts making 32lbs of boost than turbo will cheerp and boost drops down to 20lbs than while doing that it rolls black smoke than Egr temp was over 600 degrees the fan comes …Cold starts, aptly named for starting your engine in cold temperatures, have given Series 60 engines trouble. They can lose their prime and not start properly. Using a starting fluid should help combat this issue, and you shouldn’t have any other problems from it once the engine is running.

May 22, 2019 · Series 60 – Section 4.8 Radiator; Series 60 – Section 4.5 Coolant Pressure Control Cap; Series 60 – Section 4.6 Engine Cooling Fan; Series 60 – Section 4.4 Thermostat; Series 60 – Section 4.2 Water Pump (Gear-Case Mounted – 1991 and Later) (GCM) Series 60 – Section 4.3 Water Pump (Front Mounted) (Fm) Series 60 – Section 4.1 ... Detroit Series 60 won't start, there is fuel pressure, changed both sensors, Starts with fluid, but dies as soon as fluid spray stop 1999 International ... I took a 60 series Detroit out of 2003 Freightliner Columbia and put it in 1999 Freightliner FLD. It will crank along as I'm spraying ether .But goes dead when I stop spraying. Took it to ...I have 1999 freightliner century c120 DD engine series 60 I had the warning low oil pressure come on took it to the mechanic he said the oil pump is fine and the pressure is good the gauge shows good pressure from 45-50 psi at first when I start the truck the warning would come on and when the water temp reached 150 degrees and I …Keeping about 36 or 37lbs. at about 800-850 RPMs. Looks like you’re at 43, 37.5, and 21 at idle. Idle pressure might be a little low. I’d have to check mine, Same engine fresh inframe. You probably noticed increments on guage is 12.5 lbs. not 10. Detroit’s oil pressure is lower than Cats, about 10lbs. If I recall correctly.And I'm understanding that Detroit's own oil is bottled by delvac. A friend is running Schaefer's oil in his fresh engine, claims that his consumption dropped from running Chevron. But, it's not readily available on the road. My current engine has 800k on it, I service every 20k, running Chevron 15w-40, I use 2 gallons of oil between changes.Fuel Injection System: The Detroit 60 Series is equipped with a high-pressure common rail fuel injection system. This system consists of fuel injectors, a common fuel rail, a fuel pump, and an electronic control module (ECM). The ECM controls the fuel delivery based on inputs from various sensors, such as throttle position, engine speed, and ...Hi, I have a 2000 Freightliner Century with a Detroit 60 series 12.7 liter motor. The truck will not start after parking at a rest area. The last thing that happened was the idle started misfiring I revived it up and it still missed up high. The tach from from the normal 2200 to 2350 bouncing around.Left Side of Engine shown: Detroit Series 60 w/DDEC V engine controls Right side of Engine shown: Detroit Series 60 w/DDEC V engine controls Side 2. Unit injectors (under valve cover center of cylinder head) ... (starting 1987-2011): Freightliner; Sterling; Western Star; Various motor homes / motor coaches; Subscribe. Login. Notify ofTable 2. Series 60 Engine Air System, Fuel System, and Cooling System Parameters. * Exhaust systems should provide a maximum of 3.0” Hg during normal service. This applies to exhaust system devices having mufflers and diesel oxidation catalysts. Particulate filter engines may operate above 3.0” Hg specification as long as they do not exceed ...

Posted 1/12/2012 17:05 (#2158046 - in reply to #2156817) Subject: Re: ?'s about 60 series detroit made in about 1996. NC ND. '96 should be a DDECIII, would be skeptical of the 475, I've only known them to be 430-470 or 485. Blow-by is one of the better ways to know what shape the engine is in.

3600 S. Noah Dr. Saxonburg, Pa. 16056. PittsburghPower.com, 724-360-4080. Share. Back to News. Even though the Detroit Diesel Series 60 was discontinued in 2011, it's still one of the most common engines for Class 8 trucks. Some may not know about the fascinating story behind these engines. At the onset of WWII General Motors created the GM ...

Jun 14, 2011 · 13. Jun 14, 2011. San Angelo, TX. 0. Don't know as I have only had mine a couple of weeks, but sometimes after sitting maybe 2 days, mine does not want to start. It will finally fire up after cranking on it hard and it chugging like an old tin lizzie for a minute. BigfootWRL, Jun 14, 2011. #2. Jun 15, 2011 #3. DPF Cleaning Starting - $179 | We sell DPFs, Gaskets, and Clamps; Call | Text : (856) 440-3338. ... With proper cleaning, you will have your Detroit 60 series EGR problems fixed in no time. We will take a look at your Detroit 60 series EGR valve & Detroit DD15 EGR valve.Subject: 60 Series Detroit fuel bleeding back. Have a 2000 model year 12.7 in a 9900I international and if it’s been sitting more than a couple hours it needs a sniff of ether to get it started. I’ve replaced all the fuel lines from the tanks to the head and back aswell as the check valve on the back of the head a couple years ago.Detroit 60 series 14.0 liter. My air compressor don't last more than 6 months. ... I have question about the air system on a 2007 freightliner Columbia with a 14.0 Detroit series 60 . When you start the truck it builds air pressure in both primary and secondary sides of the system . ... My compressor is dumping coolant into my air tanks what ...Mar 23, 2015 · Hello all. Having a strange problem with my truck and I was hoping someone here would have a clue based on my particular symptoms. I have a 2004 Freightshaker with a 12.7 EGR Detroit 60 Series with just over 800k Mi. For the last several weeks if I turn the truck off for several hours I will... Bisbell Discussion starter. 2 posts · Joined 2016. #1 · Mar 6, 2016. I have a 1991 Peterbilt 377 with a 60 series Detroit that won't start at all. It started out starting sometimes but when it did it had a gray smoke and sounded out of time but would smooth out after a second or two and ran great going down the road, to now it won't start at all.Working on 91 detroit 11.1 60 series hard to starter up after 5 mins sitting had to use starting fuel - Answered by a verified Technician. ... Working on a 1996 international 8100 with M11 Cummins engine. I am having a problem with starting. I am having an issue with the tuck losing fuel prime.2005 columbia with 14l series 60. this engine has had an inframe done with new head and injectors. the truck starts and runs fine , but if it sits for 3 days it wont start unless you crank it for at least 2 minutes. it is like it ran out of fuel , no smoke out of the exhaust for the first minute, then starts puffing white smoke and finally starts. i have replaced the check valve …

On average, diesel fuel injectors last up to 100,000 miles. You always want to be conscious of the following symptoms, but you should be especially attentive as your engine ages. Strong fuel odor. Lower fuel efficiency. Trouble starting. Engine misfires. Low RPMs. YOU SMELL FUEL.Series 60 DDIII start up problem. I'm new to this forum and really, computers in general, so I hope I am posting this problem correctly. I have a 96 FLD120 w/12.7 DDIII that I inframed at 1,250,000 w/Reliabilt parts. Was running good, just tired and time was right. Found an injector spring broken and didnt even notice it from the way it ran,and ...so my truckhas had an inframe with 15:1 pistons and now I have horrible smoke on startup. Goes away once warm but in cold days it could take 20 mins or longer. Will be going back into it to fix the issue. Would like to know how do I find out which 16.5:1 piston kit would be and if there is one that’s a straight bolt in. It’s a ddec 3 gk motor.Few weeks ago my 2003 Freightliner Century with a Detroit 12.7 has developed a hard starting problem. It is become so hard to start that I have to use the start up fluid or else I will drain the batteries. ... stigan-turbocharger-847-1024-new-international-freightliner-detroit-diesel-series-60-c12-turbo-k.jpg. 35.8 KB Views: 295. Save Share ...Instagram:https://instagram. mainstays programmable coffee makerpunta gorda bridge accident todaypoint break financial loans reviewspokefan tf We tried to start the truck probably 100 times in the shop and "randomly" it seemed it would not fire up, just crank away forever. I read about cranking speed being important, so tried a new set of batteries, which did not improve this problem.DD Series 60 fuel check valve ... igoldin74 Bobtail Member. 1 0. May 8, 2017 0. hello comrades, I am having an issue with starting my 14l S60 after 1 day or more of sitting still. I took apart my return line check valve at the back of the engine and it looked like the first springed valve has a tiny hole in it. ... whether this was the root ... 47 north cle elumhopkinsville busted Series 60 Charge Air Cooler. On vehicle and industrial engines, a CAC (charge air cooler) is normally mounted ahead of the cooling system radiator. On keel-cooled marine engines the charge air cooler is incorporated into the keel cooler tank. On heat exchanger-cooled engines, the charge air cooler is part of the intake manifold. The …I have 1999 freightliner century c120 DD engine series 60 I had the warning low oil pressure come on took it to the mechanic he said the oil pump is fine and the pressure is good the gauge shows good pressure from 45-50 psi at first when I start the truck the warning would come on and when the water temp reached 150 degrees and I … sugar in 12 oz mountain dew Posted 3/24/2012 00:15 (#2303337 - in reply to #2303323) Subject: Re: problems with 60 series detroit in western star. NC ND. the computer can be set to limit power in certain gears, might want to have a shop check the engine/transmission power settings, have a friend who set his truck up that way, just can't remember if he lowered the power in ...Detroit 60 series 12.7 head gasket Discussion in 'Heavy Duty Diesel Truck Mechanics Forum' started by ruvim75, Dec 19, 2022. Page 1 of 2 1 2 Next > ... The front gear train lash is .006" to .009". I know Detroit Diesel doesn't recommend third party surfacing of the heads because of the complexity of fixturing, account of the fact that a ...Let me start with this... NEW: TRS/SRS INJECTORS w/ORINGS BOOST PRESURE SENSOR FUEL CHECK VALVE AT HEAD ... I occasionally see problems with fuel maps getting corrupted and weird things happen. Most common is it runs fine until you release your parking brake and then it runs rough. ... 2001 peterbilt 379 Detroit 12.7... Tylers1220 posted Apr 29 ...